HAL configuration file. More...

#include "stm32f1xx_hal_rcc.h"
#include "stm32f1xx_hal_gpio.h"
#include "stm32f1xx_hal_exti.h"
#include "stm32f1xx_hal_dma.h"
#include "stm32f1xx_hal_cortex.h"
#include "stm32f1xx_hal_flash.h"
#include "stm32f1xx_hal_i2c.h"
#include "stm32f1xx_hal_pwr.h"

Macros
#define	HAL_MODULE_ENABLED
	This is the list of modules to be used in the HAL driver. More...

#define	HAL_I2C_MODULE_ENABLED

#define	HAL_CORTEX_MODULE_ENABLED

#define	HAL_DMA_MODULE_ENABLED

#define	HAL_FLASH_MODULE_ENABLED

#define	HAL_EXTI_MODULE_ENABLED

#define	HAL_GPIO_MODULE_ENABLED

#define	HAL_PWR_MODULE_ENABLED

#define	HAL_RCC_MODULE_ENABLED

#define	HSE_VALUE 8000000U
	Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL). More...

#define	HSE_STARTUP_TIMEOUT 100U

#define	HSI_VALUE 8000000U
	Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL). More...

#define	LSI_VALUE 40000U
	Internal Low Speed oscillator (LSI) value. More...

#define	LSE_VALUE 32768U
	External Low Speed oscillator (LSE) value. This value is used by the UART, RTC HAL module to compute the system frequency. More...

#define	LSE_STARTUP_TIMEOUT 5000U

#define	VDD_VALUE 3300U
	This is the HAL system configuration section. More...

#define	TICK_INT_PRIORITY 0U

#define	USE_RTOS 0U

#define	PREFETCH_ENABLE 1U

#define	USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */

#define	USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */

#define	USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */

#define	USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */

#define	USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */

#define	USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */

#define	USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */

#define	USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */

#define	USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */

#define	USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */

#define	USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */

#define	USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */

#define	USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */

#define	USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */

#define	USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */

#define	USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */

#define	USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */

#define	USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */

#define	USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */

#define	USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */

#define	USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */

#define	USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */

#define	USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */

#define	MAC_ADDR0 2U
	Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code. More...

#define	MAC_ADDR1 0U

#define	MAC_ADDR2 0U

#define	MAC_ADDR3 0U

#define	MAC_ADDR4 0U

#define	MAC_ADDR5 0U

#define	ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */

#define	ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */

#define	ETH_RXBUFNB 8U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */

#define	ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */

#define	DP83848_PHY_ADDRESS 0x01U

#define	PHY_RESET_DELAY 0x000000FFU

#define	PHY_CONFIG_DELAY 0x00000FFFU

#define	PHY_READ_TO 0x0000FFFFU

#define	PHY_WRITE_TO 0x0000FFFFU

#define	PHY_BCR ((uint16_t)0x00)

#define	PHY_BSR ((uint16_t)0x01)

#define	PHY_RESET ((uint16_t)0x8000)

#define	PHY_LOOPBACK ((uint16_t)0x4000)

#define	PHY_FULLDUPLEX_100M ((uint16_t)0x2100)

#define	PHY_HALFDUPLEX_100M ((uint16_t)0x2000)

#define	PHY_FULLDUPLEX_10M ((uint16_t)0x0100)

#define	PHY_HALFDUPLEX_10M ((uint16_t)0x0000)

#define	PHY_AUTONEGOTIATION ((uint16_t)0x1000)

#define	PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200)

#define	PHY_POWERDOWN ((uint16_t)0x0800)

#define	PHY_ISOLATE ((uint16_t)0x0400)

#define	PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020)

#define	PHY_LINKED_STATUS ((uint16_t)0x0004)

#define	PHY_JABBER_DETECTION ((uint16_t)0x0002)

#define	PHY_SR ((uint16_t)0x10U)

#define	PHY_SPEED_STATUS ((uint16_t)0x0002U)

#define	PHY_DUPLEX_STATUS ((uint16_t)0x0004U)

#define	USE_SPI_CRC 0U

#define	assert_param(expr) ((void)0U)
	Include module's header file. More...

Detailed Description

HAL configuration file.

Attention

© Copyright (c) 2017 STMicroelectronics. All rights reserved.

This software component is licensed by ST under BSD 3-Clause license, the "License"; You may not use this file except in compliance with the License. You may obtain a copy of the License at: opensource.org/licenses/BSD-3-Clause

Definition in file stm32f1xx_hal_conf.h.

Macro Definition Documentation

◆ assert_param

#define assert_param ( expr ) ((void)0U)

Include module's header file.

Definition at line 382 of file stm32f1xx_hal_conf.h.

◆ DP83848_PHY_ADDRESS

#define DP83848_PHY_ADDRESS 0x01U

Definition at line 187 of file stm32f1xx_hal_conf.h.

◆ ETH_RX_BUF_SIZE

#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */

Definition at line 179 of file stm32f1xx_hal_conf.h.

◆ ETH_RXBUFNB

#define ETH_RXBUFNB 8U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */

Definition at line 181 of file stm32f1xx_hal_conf.h.

◆ ETH_TX_BUF_SIZE

#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */

Definition at line 180 of file stm32f1xx_hal_conf.h.

◆ ETH_TXBUFNB

#define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */

Definition at line 182 of file stm32f1xx_hal_conf.h.

◆ HAL_CORTEX_MODULE_ENABLED

#define HAL_CORTEX_MODULE_ENABLED

Definition at line 71 of file stm32f1xx_hal_conf.h.

◆ HAL_DMA_MODULE_ENABLED

#define HAL_DMA_MODULE_ENABLED

Definition at line 72 of file stm32f1xx_hal_conf.h.

◆ HAL_EXTI_MODULE_ENABLED

#define HAL_EXTI_MODULE_ENABLED

Definition at line 74 of file stm32f1xx_hal_conf.h.

◆ HAL_FLASH_MODULE_ENABLED

#define HAL_FLASH_MODULE_ENABLED

Definition at line 73 of file stm32f1xx_hal_conf.h.

◆ HAL_GPIO_MODULE_ENABLED

#define HAL_GPIO_MODULE_ENABLED

Definition at line 75 of file stm32f1xx_hal_conf.h.

◆ HAL_I2C_MODULE_ENABLED

#define HAL_I2C_MODULE_ENABLED

Definition at line 48 of file stm32f1xx_hal_conf.h.

◆ HAL_MODULE_ENABLED

#define HAL_MODULE_ENABLED

This is the list of modules to be used in the HAL driver.

Definition at line 35 of file stm32f1xx_hal_conf.h.

◆ HAL_PWR_MODULE_ENABLED

#define HAL_PWR_MODULE_ENABLED

Definition at line 76 of file stm32f1xx_hal_conf.h.

◆ HAL_RCC_MODULE_ENABLED

#define HAL_RCC_MODULE_ENABLED

Definition at line 77 of file stm32f1xx_hal_conf.h.

◆ HSE_STARTUP_TIMEOUT

#define HSE_STARTUP_TIMEOUT 100U

Time out for HSE start up, in ms

Definition at line 90 of file stm32f1xx_hal_conf.h.

◆ HSE_VALUE

#define HSE_VALUE 8000000U

Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL).

Value of the External oscillator in Hz

Definition at line 86 of file stm32f1xx_hal_conf.h.

◆ HSI_VALUE

#define HSI_VALUE 8000000U

Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL).

Value of the Internal oscillator in Hz

Definition at line 99 of file stm32f1xx_hal_conf.h.

◆ LSE_STARTUP_TIMEOUT

#define LSE_STARTUP_TIMEOUT 5000U

Time out for LSE start up, in ms

Definition at line 120 of file stm32f1xx_hal_conf.h.

◆ LSE_VALUE

#define LSE_VALUE 32768U

External Low Speed oscillator (LSE) value. This value is used by the UART, RTC HAL module to compute the system frequency.

< Value of the Internal Low Speed oscillator in Hz The real value may vary depending on the variations in voltage and temperature. Value of the External oscillator in Hz

Definition at line 116 of file stm32f1xx_hal_conf.h.

◆ LSI_VALUE

#define LSI_VALUE 40000U

Internal Low Speed oscillator (LSI) value.

LSI Typical Value in Hz

Definition at line 106 of file stm32f1xx_hal_conf.h.

◆ MAC_ADDR0

#define MAC_ADDR0 2U

Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code.

Definition at line 171 of file stm32f1xx_hal_conf.h.

◆ MAC_ADDR1

#define MAC_ADDR1 0U

Definition at line 172 of file stm32f1xx_hal_conf.h.

◆ MAC_ADDR2

#define MAC_ADDR2 0U

Definition at line 173 of file stm32f1xx_hal_conf.h.

◆ MAC_ADDR3

#define MAC_ADDR3 0U

Definition at line 174 of file stm32f1xx_hal_conf.h.

◆ MAC_ADDR4

#define MAC_ADDR4 0U

Definition at line 175 of file stm32f1xx_hal_conf.h.

◆ MAC_ADDR5

#define MAC_ADDR5 0U

Definition at line 176 of file stm32f1xx_hal_conf.h.

◆ PHY_AUTONEGO_COMPLETE

#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020)

Auto-Negotiation process completed

Definition at line 212 of file stm32f1xx_hal_conf.h.

◆ PHY_AUTONEGOTIATION

#define PHY_AUTONEGOTIATION ((uint16_t)0x1000)

Enable auto-negotiation function

Definition at line 207 of file stm32f1xx_hal_conf.h.

◆ PHY_BCR

#define PHY_BCR ((uint16_t)0x00)

Transceiver Basic Control Register

Definition at line 198 of file stm32f1xx_hal_conf.h.

◆ PHY_BSR

#define PHY_BSR ((uint16_t)0x01)

Transceiver Basic Status Register

Definition at line 199 of file stm32f1xx_hal_conf.h.

◆ PHY_CONFIG_DELAY

#define PHY_CONFIG_DELAY 0x00000FFFU

Definition at line 191 of file stm32f1xx_hal_conf.h.

◆ PHY_DUPLEX_STATUS

#define PHY_DUPLEX_STATUS ((uint16_t)0x0004U)

PHY Duplex mask

Definition at line 220 of file stm32f1xx_hal_conf.h.

◆ PHY_FULLDUPLEX_100M

#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100)

Set the full-duplex mode at 100 Mb/s

Definition at line 203 of file stm32f1xx_hal_conf.h.

◆ PHY_FULLDUPLEX_10M

#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100)

Set the full-duplex mode at 10 Mb/s

Definition at line 205 of file stm32f1xx_hal_conf.h.

◆ PHY_HALFDUPLEX_100M

#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000)

Set the half-duplex mode at 100 Mb/s

Definition at line 204 of file stm32f1xx_hal_conf.h.

◆ PHY_HALFDUPLEX_10M

#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000)

Set the half-duplex mode at 10 Mb/s

Definition at line 206 of file stm32f1xx_hal_conf.h.

◆ PHY_ISOLATE

#define PHY_ISOLATE ((uint16_t)0x0400)

Isolate PHY from MII

Definition at line 210 of file stm32f1xx_hal_conf.h.

◆ PHY_JABBER_DETECTION

#define PHY_JABBER_DETECTION ((uint16_t)0x0002)

Jabber condition detected

Definition at line 214 of file stm32f1xx_hal_conf.h.

◆ PHY_LINKED_STATUS

#define PHY_LINKED_STATUS ((uint16_t)0x0004)

Valid link established

Definition at line 213 of file stm32f1xx_hal_conf.h.

◆ PHY_LOOPBACK

#define PHY_LOOPBACK ((uint16_t)0x4000)

Select loop-back mode

Definition at line 202 of file stm32f1xx_hal_conf.h.

◆ PHY_POWERDOWN

#define PHY_POWERDOWN ((uint16_t)0x0800)

Select the power down mode

Definition at line 209 of file stm32f1xx_hal_conf.h.

◆ PHY_READ_TO

#define PHY_READ_TO 0x0000FFFFU

Definition at line 193 of file stm32f1xx_hal_conf.h.

◆ PHY_RESET

#define PHY_RESET ((uint16_t)0x8000)

PHY Reset

Definition at line 201 of file stm32f1xx_hal_conf.h.

◆ PHY_RESET_DELAY

#define PHY_RESET_DELAY 0x000000FFU

Definition at line 189 of file stm32f1xx_hal_conf.h.

◆ PHY_RESTART_AUTONEGOTIATION

#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200)

Restart auto-negotiation function

Definition at line 208 of file stm32f1xx_hal_conf.h.

◆ PHY_SPEED_STATUS

#define PHY_SPEED_STATUS ((uint16_t)0x0002U)

PHY Speed mask

Definition at line 219 of file stm32f1xx_hal_conf.h.

◆ PHY_SR

#define PHY_SR ((uint16_t)0x10U)

PHY status register Offset

Definition at line 217 of file stm32f1xx_hal_conf.h.

◆ PHY_WRITE_TO

#define PHY_WRITE_TO 0x0000FFFFU

Definition at line 194 of file stm32f1xx_hal_conf.h.

◆ PREFETCH_ENABLE

#define PREFETCH_ENABLE 1U

Definition at line 133 of file stm32f1xx_hal_conf.h.

◆ TICK_INT_PRIORITY

#define TICK_INT_PRIORITY 0U

tick interrupt priority (lowest by default)

Definition at line 131 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_ADC_REGISTER_CALLBACKS

#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */

Definition at line 135 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_CAN_REGISTER_CALLBACKS

#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */

Definition at line 136 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_CEC_REGISTER_CALLBACKS

#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */

Definition at line 137 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_DAC_REGISTER_CALLBACKS

#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */

Definition at line 138 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_ETH_REGISTER_CALLBACKS

#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */

Definition at line 139 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_HCD_REGISTER_CALLBACKS

#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */

Definition at line 140 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_I2C_REGISTER_CALLBACKS

#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */

Definition at line 141 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_I2S_REGISTER_CALLBACKS

#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */

Definition at line 142 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_IRDA_REGISTER_CALLBACKS

#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */

Definition at line 151 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_MMC_REGISTER_CALLBACKS

#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */

Definition at line 143 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_NAND_REGISTER_CALLBACKS

#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */

Definition at line 144 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_NOR_REGISTER_CALLBACKS

#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */

Definition at line 145 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_PCCARD_REGISTER_CALLBACKS

#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */

Definition at line 146 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_PCD_REGISTER_CALLBACKS

#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */

Definition at line 147 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_RTC_REGISTER_CALLBACKS

#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */

Definition at line 148 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_SD_REGISTER_CALLBACKS

#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */

Definition at line 149 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_SMARTCARD_REGISTER_CALLBACKS

#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */

Definition at line 150 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_SPI_REGISTER_CALLBACKS

#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */

Definition at line 153 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_SRAM_REGISTER_CALLBACKS

#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */

Definition at line 152 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_TIM_REGISTER_CALLBACKS

#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */

Definition at line 154 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_UART_REGISTER_CALLBACKS

#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */

Definition at line 155 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_USART_REGISTER_CALLBACKS

#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */

Definition at line 156 of file stm32f1xx_hal_conf.h.

◆ USE_HAL_WWDG_REGISTER_CALLBACKS

#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */

Definition at line 157 of file stm32f1xx_hal_conf.h.

◆ USE_RTOS

#define USE_RTOS 0U

Definition at line 132 of file stm32f1xx_hal_conf.h.

◆ USE_SPI_CRC

#define USE_SPI_CRC 0U

Definition at line 229 of file stm32f1xx_hal_conf.h.

◆ VDD_VALUE

#define VDD_VALUE 3300U

This is the HAL system configuration section.

Value of VDD in mv

Definition at line 130 of file stm32f1xx_hal_conf.h.

Macros